700 Series: Supreme, Munic and MX/6
800 Series: Corrugated 7/8ʺ
1500 Series: Commercial 36, Industrial 36 and Ancestral
Trims for roofing
Universal ridge caps
FTU (Unic ridge cap)
EFTU (Unic cap)
FT-6, FT-8 and FT-12
FT-MT
FT-125 and FT-124
Notched ridge caps
FTE
Vented ridge caps
FV
FDV (Vented dome)
EFV (Endcap for vented ridge cap)
Universal hip caps
A-145 (Hip)
FIC-245 (Finishing)
FIM-345 (Finishing)
FIC-345 (Finishing)
Notched hip caps and finishing strips
ARE (Notched Hip)
FIE (Notched Finishing)
Roof flashing
S-04, S-425 and S-450
S-04B and S-425B
2567 (Aluminium)
Universal valley
NA-6-9-12-18 (TYPE A)
NB-8-11-17 (TYPE B)
NC-4-7-13 (TYPE C)
ND-4-7 (TYPE D)
Trims for siding
Standard trims
705, 805 and 1505 (J molding)
702, 802 and 1502 (J molding)
709 and 1509 (Starter)
609, 708 and 1508 (Starter)
703 and 1503 (Drip)
710 and 1510 (Drip)
716 and 1516 (Drip)
713, 813 and 1513 (Anti-intrusion)
Corner trims
700, 800 and 1500 (Exterior corner)
717 and 1517 (Exterior corner)
745 and 845 (Exterior corner at 45º)
714 and 814 (Interior corner)
724 and 1524 (Interior corner)
706, 806 and 1506 (Interior corner)
707, 807 and 1507 (Conversion)
712, 812 and 1512 (Conversion)
704, 804 and 1504 (Partition)
611, 711, 811, 651, 751 and 851 (Soffit and wall joint)
Trims for l’Ancestral
Ridge caps
FT-6, FT-8 and FT-12
FA-5, FA-7 and FA-11
FT-125
FTB-4 and FTB-6
FTMT
FTMTA
FTU (Unic ridge cap)
EFTU (Unic end cap)
Starter strips and flashing
DPR (Gable starter Roger)
DP (Gable starter)
DPP (Flat gable starter)
DL (Lateral starter)
DTA-212 and DTA-412 (Roof drip)
DTA-512 (Roof drip)
DT-1212 (Roof drip)
S-04B
Roof accessory
Ancestral end cap
Finishing flashing
FI (Finishing molding)
FIB (Low finishing molding)
Clips and fasteners
AE (Notching clamp)
JFA (Ridge cap J for clampling)
AP (Gable clamp)
AF (Fascia clamp)
AL (Lateral clamp)
Trims for Toscan
Universal ridge caps
FTU-TOS (Unic ridge cap)
EFTU-TOS (Unic end cap)
Standard trims
S-TOSR
S-TOS2
NB11R
F-TOSR (Finishing)
J-TOSR (J molding)
FIM-345 (Finishing)
A-145 (Hip)
Trims for Distinction
JDIS (J molding)
PDIS (Partition)
DDIS (Galvanized starter)
CDIS (Conversion)
CEDIS (Exterior corner)
EDIS (Drip)
CIDIS (Interior corner)
Flat steel
Flat steel in sheets
Prefinished, galvanized, or Galvalume Plus
Dimensions :
- 36’’ x 120’’ (28 ga)
- 48’’ x 120’’ (26 ga and 24 ga)
- 48’’ x 96’’ (26 ga and 24 ga)
- Also available in 22 ga
*Please inquire for availability of colours and thicknesses.
Flat sheet in rolls
Prefinished, Galvanized or Galvalume Plus
Dimensions :
- 36’’ x 50’ (28 ga)
- 24’’ x 75’ (26 ga)
*Please inquire for availability of colours and thicknesses.